12.3.1 Type term_t: a reference to a Prolog term

The principal data type is term_t. Type term_t is what Quintus calls QP_term_ref. This name indicates better what the type represents: it is a handle for a term rather than the term itself. Terms can only be represented and manipulated using this type, as this is the only safe way to ensure the Prolog kernel is aware of all terms referenced by foreign code and thus allows the kernel to perform garbage collection and/or stack-shifts while foreign code is active, for example during a callback from C.

A term reference is a C uintptr_t, representing the offset of a variable on the Prolog environment stack. A foreign function is passed term references for the predicate arguments, one for each argument. If references for intermediate results are needed, such references may be created using PL_new_term_ref() or PL_new_term_refs(). These references normally live till the foreign function returns control back to Prolog. Their scope can be explicitly limited using PL_open_foreign_frame() and PL_close_foreign_frame()/PL_discard_foreign_frame().

A term_t always refers to a valid Prolog term (variable, atom, integer, float or compound term). A term lives either until backtracking takes us back to a point before the term was created, the garbage collector has collected the term, or the term was created after a PL_open_foreign_frame() and PL_discard_foreign_frame() has been called.

The foreign interface functions can either read, unify or write to term references. In this document we use the following notation for arguments of type term_t:

term_t +t	Accessed in read-mode. The‘+' indicates the argument is‘input'.
term_t -t	Accessed in write-mode.
term_t ?t	Accessed in unify-mode.

WARNING Term references that are accessed in‘write' (-) mode will refer to an invalid term if the term is allocated on the global stack and backtracking takes us back to a point before the term was written.^{212This could have been avoided by trailing term references when data is written to them. This seriously hurts performance in some scenarios though. If this is desired, use PL_put_variable() followed by one of the PL_unify_*() functions.} Compound terms, dicts, large integers, rational numbers, floats and strings are all allocated on the global stack. Below is a typical scenario where this may happen. The first solution writes a term extracted from the solution into a. After the system backtracks due to PL_next_solution(), a becomes a reference to a term that no longer exists.

term_t a = PL_new_term_ref();
...
query = PL_open_query(...);
while(PL_next_solution(query))
{ PL_get_arg(i, ..., a);
}
PL_close_query(query);

There are two solutions to this problem. One is to scope the term reference using PL_open_foreign_frame() and PL_close_foreign_frame() and makes sure it goes out of scope before backtracking happens. The other is to clear the term reference using PL_put_variable() before backtracking.

Term references are obtained in any of the following ways:

• Passed as argument
  The C functions implementing foreign predicates are passed their arguments as term references. These references may be read or unified. Writing to these variables causes undefined behaviour.
• Created by PL_new_term_ref()
  A term created by PL_new_term_ref() is normally used to build temporary terms or to be written by one of the interface functions. For example, PL_get_arg() writes a reference to the term argument in its last argument.
• Created by PL_new_term_refs(size_t n)
  This function returns a set of term references with the same characteristics as PL_new_term_ref(). See PL_open_query().
• Created by PL_copy_term_ref(term_t t)
  Creates a new term reference to the same term as the argument. The term may be written to. See figure 6.

Term references can safely be copied to other C variables of type term_t, but all copies will always refer to the same term.

term_t PL_new_term_ref()

Return a fresh reference to a term. The reference is allocated on the local stack. Allocating a term reference may trigger a stack-shift on machines that cannot use sparse memory management for allocation of the Prolog stacks. The returned reference describes a variable. Raise a resource exception and returns (term_t)0 on failure.

term_t PL_new_term_refs(size_t n)

Return n new term references. The first term reference is returned. The others are t+1, t+2, etc. Raise a resource exception and returns (term_t)0 on failure. There are two reasons for using this function. PL_open_query() and PL_cons_functor() expect the arguments as a set of consecutive term references, and very time-critical code requiring a number of term references can be written as:

pl_mypredicate(term_t a0, term_t a1)
{ term_t t0 = PL_new_term_refs(2);
  term_t t1 = t0+1;

  ...
}

term_t PL_copy_term_ref(term_t from)

Create a new term reference and make it point initially to the same term as from. This function is commonly used to copy a predicate argument to a term reference that may be written. Raise a resource exception and returns (term_t)0 on failure. An example of its use is given below, in the sample code pl_write_atoms().

void PL_reset_term_refs(term_t after)

Destroy all term references that have been created after after, including after itself. Any reference to the invalidated term references after this call results in undefined behaviour.

Note that returning from the foreign context to Prolog will reclaim all references used in the foreign context. This call is only necessary if references are created inside a loop that never exits back to Prolog. See also PL_open_foreign_frame(), PL_close_foreign_frame() and PL_discard_foreign_frame().

12.3.1.1 Interaction with the garbage collector and stack-shifter

Prolog implements two mechanisms for avoiding stack overflow: garbage collection and stack expansion. On machines that allow for it, Prolog will use virtual memory management to detect stack overflow and expand the runtime stacks. On other machines Prolog will reallocate the stacks and update all pointers to them. To do so, Prolog needs to know which data is referenced by C code. As all Prolog data known by C is referenced through term references (term_t), Prolog has all the information necessary to perform its memory management without special precautions from the C programmer.